Tile provides a durable surface, especially in areas with high levels of humidity or repeated exposure to moisture. Placing the tile over a waterproof underlayment provides another layer of protection against water damage.
Drylock is a construction product that adds an element of waterproof protection to floors and walls. With proper application and preparation, Drylock is suitable for use under tiles. United Glisonite Laboratories manufactures Drylock products. These waterproof substances come in a variety of formulas for masonry surfaces. Powdered products require mixing with water, while others are ready to apply from the container. Once the Drylock cures, it forms a durable surface that repels water.
The cured Drylock also provides an ideal base coat for finishing with paint or other topical products. For tile to adhere to an underlying surface, it requires a waterproof surface.
Tiling over a porous surface can result in warping beneath the tiles and lifting of the tiles. A waterproof backing helps hold the tiles firmly in place by keeping water from breaking the bond beneath the bottoms of the tiles. Correct preparation plays a key role in creating a long-lasting, durable tile surface. Waterproofed masonry surfaces provide ideal surfaces for tile installation.
Check the masonry floor for unevenness. If your floor has high spots, grind them down with a belt or disc sander.
Fill in any low spots with a liquid concrete leveling product. Apply the Drylock to these patched areas, creating a smooth expanse of waterproofed masonry. Start by cleaning the surface with warm water and a mild detergent, scrubbing the area to remove any visible surface debris and stains, especially greasy, oily substances. In many areas of your home, tiling over damp areas requires the placement of a waterproof membrane, such as cement board. Since Drylock acts as a waterproofing agent, your surface is ready for the adhesive coat and the tiles.
Follow the manufacturer's instructions when determining the thickness of the adhesive and the grout. Using adequate amounts of these products will help ensure a durable tile finish.
Laura Wallace Henderson, a professional freelance writer, began writing in Her articles appear online at Biz Mojo, Walden University and various other websites. She has served as the co-editor for "Kansas Women: Focus on Health. Can You Tile Over Drylock? Hunker may earn compensation through affiliate links in this story. Tile works best over waterproof surfaces. Share this article. Laura Wallace Henderson. Show Comments.It comes in ready-mixed white and gray, and delivers a sandy finish that mimics the look of real concrete.
Plus, soap and water cleanup is quick and easy! Bird lovers know, left untreated, a bird bath attracts mold and mildew, and cleaning becomes that tiresome chore everyone avoids.
The next time you scrub it clean, let it dry for at least 48 hours. Let it dry for one week, then add fresh water. From here on out, maintenance should be much easier! Providing a clean, safe swimming environment means paying attention to water quality and structural integrity.
Formulated to resist water pressure of 15 lbs. The original bright white color comes in a smooth finish and can be tinted to a variety of cool shades. Apply according to directions, wait a week before refilling the pool, and enjoy!
Currently growing in popularity, cooking outdoors is often the focal point of a perfect patio party! Handy do-it-yourselfers are getting more and more innovative, incorporating concrete, brick, stucco and other masonry materials to build custom creations that are the envy of the neighborhood.
The major downside of concrete, however, is the natural porosity that makes it susceptible to water penetration, seepage and ice damage. A distinctive splash of personality in any outdoor living space, a fish pond must withstand the kind of constant, consistent water pressure that has been proven to degrade concrete.
Just like concrete, terra cotta is a porous material that will break down, dust, pit, crack, and stain when subjected to weather, water and UV rays. The only way to prevent damage and deterioration is to protect it with a good quality sealer. You can also use this multi-purpose product on concrete driveways, basement floors, garage floors, concrete sidewalks, patios, terrazzo, brick, and slate. As large outdoor murals typically require incredible effort, creativity and funds, taking steps toward preservation should be a top priority.
Outdoor, precast concrete water troughs, holding tanks, cisterns and bowls are subjected to interior water pressure as well as exterior hail, rain, snow and harsh sunlight. The result? Pitting and crumbling. The solution? The lightweight powder is easy to carry out into the field and mixes with water — right on the spot — for quick and easy application.
Holiday Crafts, Decorations and Props.UGL has been manufacturing paints, stains, and finishes since As such, it does not peel off like traditional paint. It is also resistant to a wide range of potential contaminants, include salt from roads, grease, oil, and water. In fact, they were the first U. The founder, Gerald B. In its earliest days, UGL produced asphalt and roofing products. The business grew rapidly, leading the business to relocate to a larger space. The line was seen as a DIY solution for waterproofing wet basements, stopping masonry leaks, protecting masonry, and protecting concrete floors.
Over the course of time, products and improvements have been added to the Drylok line. Today, UGL is managed by its fourth president. The company continues to produce Drylok Cement Floor Paint as well as many other home improvement products. Currently, they are relaunching their Zar line to include luxury options with custom color blends.
In fact, it differs rather dramatically when compared to traditional paints. Check out the section below to learn more about Drylok Concrete Floor Paint and find out what we think about this unique home improvement product. Drylok Latex Concrete Floor Paint is designed to protect and decorate masonry and wood surfaces in private industrial settings. It is available in nine ready-mixed colors as well as a dark tinted base that is suitable for custom color blends.
The paint comes in gallon paint jugs, each of which is expected to cover between and square feet. The concrete paint can even adhere to a damp surface. According to the manufacturer, Drylok can be used on garage floors, basement floors, brick patios, poured concrete and block patios, and wood steps.
It can be used to prolong the life of and beautify these surfaces. Premixed color options include white, gull gray, Dover gray, soft gray, Persian red, Bamboo beige, terracotta, and Georgetown gray.
Available tints include caramel, deep charcoal, platinum, and spruce. Drylok provides select surfaces with a flat, non-slip finish. Unlike traditional paint, it can withstand frequent traffic, weather, washings, and other abuses. On top of that, it is moisture-resistant, odorless, and generally durable.
It can even be used to revitalize worn painted surfaces. While many consumers opt to use Drylok to for complete coverage, it can also be used to stencil patterns and logos.
There are several brands of latex concrete floor paints as well as other masonry paints and stains. This acrylic anti-slip concrete coating is very similar to Drylok Concrete Floor Paint. Like Drylok, it is engineered to withstand regular exposure to foot traffic, weather, and other abuse. It is even mold and mildew resistant.
Like Drylok, it is sold by the gallon.Drylok is an interior latex paint that serves double duty as a waterproofing agent for previously uncoated concrete, masonry or cinder block basement walls. Properly applied, Drylok can prevent moisture from seeping through porous concrete. Improperly applied, the waterproofing function of the paint is likely to fail, leading to ugly mold and mildew stains. With thorough surface prep of the walls, however, the Drylok bonds firmly to the concrete and do its part in keeping moisture out of the basement.
Slip on a face mask and safety eyewear to protect your respiratory system and eyes from any harsh dusty residue released into the air by the cleaning process. Examine the walls carefully for any cracks, gaps or white scaly build-up. The white build-up is called efflorescence, and brushing alone is not likely to remove it entirely. Slip on a pair of vinyl gloves. Apply undiluted vinegar to the sponge, Rub the sponge onto efflorescence until the material is dissolved.
Apply more vinegar to the sponge if needed. Soak the sponge in a bucket of warm water, then use it to rinse off any residual vinegar from the concrete. Wipe the affected area dry with clean rag. Fill any cracks you discovered during Step 3 with a hydraulic cement. This material is normally supplied as a ready-mix powder that must be mixed according to the manufacturer's instructions.
Smooth the hydraulic cement into each crack or gap and smooth the surface level with a putty knife. Mike Matthews is editor of Green Building Product News, a national publication that covers sustainable innovations in building and remodeling, and he has spoken at national conferences on green building.
He has also served as founding editor of "Paint Dealer" magazine. Skip to main content. Tip While a bristled scrub brush should be adequate for scraping newer concrete walls in Step 2, a wire brush would a better choice for older walls that may have a greater build-up of accumulated dirt.
Warning Drylok should not be applied to a wall that has been painted previously with a conventional oil or latex paint. Older paint layers would need to be stripped away to allow the waterproofing function of Drylok to be effective. About the Author Mike Matthews is editor of Green Building Product News, a national publication that covers sustainable innovations in building and remodeling, and he has spoken at national conferences on green building.
Customer Service Newsroom Contacts.Recently I had to remodel one of my rental homes. And I was teetering with the idea of not touching the basement. Side Note: as I was painting the walls in the basement I noticed our neighbors had their downspout facing my foundation.
Can You Tile Over Drylock?
But that explains some of the moisture in the basement. The walls are constantly moist and some of the old paint was pealing.
And an angle grinder with a Sawtec blade to knockdown any high spots. My goal was to make the walls as smooth as possible. Mix three parts powder to one part water and stir well with a putty knife. Use a hammer and chisel for that. I love hydraulic cement because it works fast and is simple to use. Efflorescence should be removed with muriatic acid, but have good air circulation as this is potent stuff. I toyed with the idea of using a paint sprayer but decided against it.
Simply because I had the brushes and there were areas in this basement where a brush was better. The drop cloth saved my butt a few times when I got a little messy with the paint. Always wear protection when prepping or painting walls. The above links go to either Amazon or Home Depot.
I tried to find the cheapest prices for each item. Hope that helps.Flex Seal Liquid review
It made a huge difference in the basements smell and appearance. Get Our Guide. Thanks for another great video, Jeff. Would this product work on the concrete floor of my house?
I need to fix a problem with the linoleum turning gray in spots — I assume the problem is water. What do you think? Sounds like you have a water problem under the floor.A waterproofing chemical for masonry walls and floors, DRYLOK is ideal for basement walls and areas where water is seeping in through the concrete. The interior paint on the concrete surface must be in good condition -- not peeling or cracking.
DRYLOK loses its waterproofing ability when applying the chemical over painted walls or flooring containing latex or oil-based paint. The chemical cannot seep into the masonry's pores due to the paint.
Drylok Concrete Floor Paint Review
You can still apply DRYLOK over latex or oil-based paint but the chemical will not prevent moisture from seeping in through the concrete wall or flooring.
The painted walls or flooring you want to coat with DRYLOK must be free of any dust, dirt and debris -- completely clean.
Otherwise, the chemical will not adhere properly to the surface. Use a piece of or grit sandpaper to smooth out any rough areas on the painted wall including peeling and cracking paint. Wipe the walls or flooring with a wet cloth to remove any debris left after sanding. Dip a cotton ball or swab in a bottle of alcohol. Rub the cotton ball or swab back and forth over a small area of the wall or floor you want to paint.
If paint transfers onto the ball or swab, the paint on the wall or floor is latex. If it doesn't come off, the paint is oil-based. Move any furnishings and rugs out of the room or area you want to paint. Open any windows and doors leading into and out of the room so air can flow throughout the area. The waterproofing chemical is thick and rolls on easily over other paints. Again, open any windows and doors in the room or area you are waiting so air can flow properly and keep any fumes from overcoming you.
Nick Davis is a freelance writer specializing in technical, travel and entertainment articles. He holds a bachelor's degree in journalism from the University of Memphis and an associate degree in computer information systems from the State Technical Institute at Memphis.
He is currently living in Albuquerque, N. By Nick Davis. Hunker may earn compensation through affiliate links in this story.
Share this article. Nick Davis. Show Comments.First, let me say that if you are reading this you are head and shoulders above the mass of the population that will haphazardly sheetrock and carpet a basement without concern for the inherent problems that traditional finished basements are known for within my industry.
My only concern is that the ideas contained in this article gain wide acceptance and my revenue decreases dramatically. Few of these ideas are original. If done right, a nice profit and many enjoyable years can grow out of your healthy, well-designed basement. If done wrong or without proper attention to the crucial details, other things will grow out of - and in - your basement.
Mold Mold spores are like microscopic seeds that are constantly floating around in the air. In fact, unless you are highly sensitive or there is a large concentration of spores as a result of a mold growth problem near where you are now sitting, the air you are now breathing contains mold spores that are probably not bothering you in the least.
Mold spores are literally everywhere; on your clothing, your eyeglasses, the face of your watch, your kitchen table. This is unavoidable. Mold growth occurs when a few specific factors are present. Of all of the above factors, moisture is the most easily controlled.
In fact, few of the other factors are easily or cost-effectively dealt with. So, control moisture you must. Also at play is the type of building materials and the way they interact and integrate in modern construction. The way we have built and continue to build homes since the s energy crisis, and what we build them with, makes it very easy for mold growth to occur indoors.
Most builders use low-cost materials, over-insulate and insist on putting basements into buildings built in areas with poor soil drainage or high water tables.
When it comes to finishing basements, you have more choices and — at the same time — more problems. Since it is a much smaller space than the rest of the structure, you can spend more money on the specialized building materials that resist moisture and mold growth.
In fact, many of the solutions are twice the price but worth every penny. The way I figure it, you can spend twice as much once and do it right, or you can do it wrong and spend half as much, but end up doing it twice. In addition to donations, I accept Thank You cards. This means you can thank me for saving you tons of money in advance.
I really like the Thank You cards. If you want to know whether you have a true French drain or not, this requires some investigation. If you want confirmation, open your phone book to Waterproofing and call a few of them to come and take a look. Be prepared to endure a sales pitch and sift through the B. But you should be able to find out what kind of drainage you have….
Oh, and good luck. Ask the experts. Name Email Phone Question Want an appointment? Meet with one of our Online Consultants. I am also going to forward this letter to our family sinus doctor, Dr. Scott Kay New Jersey: New York City: Got mold questions?
Name Email Phone Question. Want an appointment? Meet with one of our Online Consultants Go.